Posted in

Do other check valves cause pressure drop?

Hey everyone, let’s cut to the chase. If you’re a piping system pro, plant manager, or just someone who deals with fluid flow day-to-day, you’ve probably wrestled with pressure drop. It’s that annoying little loss of system pressure that throws off your designs, your efficiency, and even your bottom line. And if you’ve ever shopped around for check valves, you’ve likely wondered: Do other check valves cause pressure drop, too — or is that only a thing with certain types? Other Check Valve

Full disclosure first: I’m from a check valve supplier (I’ll keep it casual here, no stuffy corporate jargon) and I work with all kinds of check valves, including the ones we call “other types” — you know, the ones that aren’t the swing or ball check valves everyone’s familiar with. Most people only hear about swing or ball valves when they talk about backflow prevention, but there’s a whole world out there: lift check, dual plate, in-line, spring-loaded, even some specialty ones for harsh environments. And yeah, every single one of those “other” check valves will cause some pressure drop. But let’s not jump to conclusions — it’s not as simple as “all check valves suck pressure” (pun intended, but keep it fair). The key is how much, and whether it’s a problem for your specific system.

First, let’s get on the same page about what pressure drop even is. Pressure drop, for anyone new to the game, is the reduction in fluid pressure that happens when it flows through a component — in this case, a check valve. It’s caused by two main things: friction between the fluid and the valve’s internal parts, and the turbulence that happens when the fluid has to change direction or squeeze through gaps to get past the valve’s closure mechanism. For a check valve, that closure mechanism is what makes it work: it opens when flow goes the right way, and slams (or closes gently) when flow tries to reverse. That mechanism is where most of the pressure loss comes from.

Now, let’s break down why “other” check valves are different from the swing or ball ones you might have worked with. Swing check valves are the OG, right? They have a hinged disc that swings out of the way when flow pushes it, so when it’s fully open, the disc is almost parallel to the pipe wall. That means a lot of flow area is open, so pressure drop is pretty low — usually between 0.5 to 2 psi for most industrial fluids, depending on flow rate. Ball check valves use a metal or rubber ball that lifts off a seat when flow pushes it, but they often have smaller ports or the ball can rattle around, so their drop is a bit higher, like 1 to 3 psi. But what about those “other” check valves? Let’s take spring-loaded lift check valves, for example. These have a disc that’s pushed closed by a spring, and the spring has to compress to let flow through. Even when fully open, the spring and the disc take up space in the pipe, so flow has to squeeze through that gap. Turbulence gets worse here, so pressure drop can jump to 2 to 5 psi — sometimes even higher if the spring is too stiff, which makes it harder for low-flow systems to open the valve properly.

Wait, dual plate check valves are another common “other” type, especially for large pipes in commercial HVAC or power plants. They have two hinged plates that fold back against the pipe wall when open, similar to a swing check but with a smaller footprint. But here’s the catch: even when fully open, the plates create a slight obstruction, and the edge where the two plates meet can cause friction. Their pressure drop is usually around 1.5 to 3 psi — so a bit more than swing check, but less than spring-loaded lift. But I’ve seen some cheap dual plate valves where the plates aren’t aligned right, so the gap gets narrower, and pressure drop spikes to 6 psi just like that. That’s why quality matters, even for “other” valves.

Now, let’s talk about specialty check valves — the ones that are often overlooked, hence the “other” label. For example, axial check valves, which are used in high-flow, low-pressure systems. These have a piston-like closure that moves along the axis of the pipe, so when open, it doesn’t create much obstruction, right? Wrong — even axial valves have a seal around the piston that rubs against the pipe wall, causing small friction loss, and the piston’s movement can create a tiny amount of turbulence. Their pressure drop is still lower than many other “other” valves, around 1 to 2 psi, but if you’re running a system at ultra-low pressure (like less than 10 psi total), even 1 psi of drop is a big deal. That’s the thing: pressure drop isn’t just a number — it’s relative to your system’s operating pressure. If your system runs at 50 psi, a 3 psi drop is 6% loss, which is manageable. If it runs at 15 psi, that same 3 psi is 20% loss — that’s a problem.

Another “other” type: wafer check valves, which are super common in small piping jobs because they’re thin and easy to install between flanges. Wait, no — wafer is a category, but some wafer check valves are the swing type, but many are the “dual plate” type, which we already talked about. But let’s not confuse categories here. The point is, any check valve that’s not a basic swing or ball falls into the “other” bucket for most people, and all of them have pressure drop because they have a closure mechanism that creates some flow restriction.

Now, why do so many people ask if “other” check valves cause pressure drop? Because some manufacturers market certain valves as “low-drop,” and folks assume “other” ones don’t. That’s a myth. Every check valve, regardless of type, will cause at least a tiny bit of pressure drop — there’s no such thing as a zero-drop check valve. The only question is how much, and whether you can mitigate it.

Wait, let’s get into the science a little more, because I don’t want to be all vague. Pressure drop across a check valve is usually measured using a formula: ΔP = (K * (v² * ρ)) / (2g), where K is the resistance coefficient specific to the valve, v is flow velocity, ρ is fluid density, and g is gravity. So K is the big one here — that’s the number that tells you how much a valve resists flow. For swing check valves, K is around 0.5 to 1.5, while spring-loaded lift check valves have K values from 2 to 5. Axial check valves have K as low as 0.8, which is why their drop is lower. So if you know your valve’s K factor, you can calculate the exact pressure drop for your system. That’s a way better approach than guessing if “other” valves cause drop — you just look up their K rating (good suppliers will give this to you, no hiding it) and do the math.

But here’s the thing: pressure drop isn’t always a bad thing. Wait, hear me out. Sometimes, a little extra pressure drop is intentional. For example, if you have a system where flow can reverse rapidly, a check valve with a bit more pressure drop might close faster, preventing water hammer. Water hammer is that loud, violent bang that can destroy pipes and equipment, so a slight pressure drop trade-off might be worth it. If you’re dealing with water hammer, a spring-loaded check valve (which closes quicker than swing) might be better than a low-drop swing valve, even if it causes a bit more pressure loss.

I’ve seen this first-hand with a plant client a couple months back. They were using swing check valves in their cooling tower system, and they kept getting water hammer every time a pump shut off. They asked us about “other” check valves, and we recommended dual plate check valves. The initial worry was: “Will the dual plate cause too much pressure drop?” We calculated it would be 2 psi more than the swing valves, but their system operates at 80 psi, so that was a 2.5% loss — nothing. And the dual plate closed faster, eliminating the water hammer, which saved them $10k+ in pipe repairs every quarter. So it’s a balance, not a one-size-fits-all.

Another example: a small residential plumbing system. Wait, even residential has check valves — for sump pumps, water main backflow preventers. A lot of residential folks use wafer check valves (another “other” type) because they’re easy to install in tight spaces. The pressure drop here is small, maybe 1 psi, but if your home has low water pressure (like from a well), that 1 psi can make your showers feel weak. In that case, you’d want a lower K valve, like an axial check valve, even if it costs a bit more. The key is matching the valve’s pressure drop to your system’s needs.

Now, let’s address the elephant in the room: some “other” check valves do have way higher pressure drop than they should, because of cheap manufacturing. I’ve seen no-name dual plate valves where the plates are made of thin, flimsy metal that warps, creating a narrow gap that restricts flow so much pressure drop jumps to 8 psi. That’s not a property of “other” check valves — that’s a property of bad valves. If you’re sourcing from a reputable supplier (that’s us, by the way), they’ll test their valves to measure pressure drop, and provide clear K factors, so you know exactly what you’re getting. No guesswork, no hidden fees for extra power to make up for pressure loss.

Wait, let’s clear up another confusion: check valves vs. backflow preventers. A lot of people group them together, but backflow preventers are a type of check valve, often with two check valves in series, which means double the pressure drop. But that’s a separate conversation — the question here is about “other check valves,” so regular single check valves, not backflow assemblies.

So to sum up the science: every check valve, including all the “other” types, causes pressure drop. The amount depends on the valve’s design (closure mechanism, spring strength, port size), the fluid’s flow rate and density, and the valve’s quality. Swing check valves are among the lowest-drop “standard” valves, while spring-loaded lift or poorly made dual plate check valves have higher drop. Specialty valves like axial are in between.

Now, what does this mean for you? If you’re designing a new system, or replacing check valves in an old one, don’t just go with the familiar swing valve without checking your pressure requirements. If you have a high-flow, low-pressure system, go for a lower-drop “other” valve like axial. If you have a problem with water hammer, a slightly higher-drop dual plate or spring-loaded check valve might be the better pick. And always ask your supplier for the valve’s K factor — that’s the only way to accurately calculate pressure drop, no surprises.

I know a lot of folks stick to what they know, but “other” check valves aren’t the boogeyman for pressure drop. They’re just different designs for different jobs. The mistake is assuming that all “other” valves cause unnecessary loss — no, it’s about matching the valve to your specific needs. If you’re worried about pressure drop affecting your system’s efficiency, or you’re dealing with water hammer and standard swing valves aren’t cutting it, don’t guess. Hit us up to chat through your piping setup, what fluids you’re moving, your flow rates, and what problems you’re facing. We can walk you through which check valve (even the “other” ones) will give you the right balance of backflow prevention and minimal pressure loss, no jargon, no fluff.

Pipeline Valve At the end of the day, pressure drop is just a part of working with fluid systems — the goal is to manage it, not eliminate it. “Other” check valves are a tool in that management, not a flaw. You just need to pick the right one for your job, and that’s where we come in. If you’re ready to stop guessing and start getting tailored advice on which check valve works best for your piping, reach out to connect and talk shop.


Wenzhou Zhenshun Valve Co., Ltd.
As one of the most professional other check valve manufacturers and suppliers in China, we’re featured by quality products and low price. Please rest assured to buy cheap other check valve made in China here from our factory. Also, quotation is available.
Address: Heyi Industrial Zone, Oubei Street, Yongjia County Wenzhou, Zhejiang China
E-mail: info@zshvvalve.com
WebSite: https://www.zshvvalve.com/