{"id":3870,"date":"2026-11-22T09:49:53","date_gmt":"2026-11-22T01:49:53","guid":{"rendered":"http:\/\/www.weeklywineshow.com\/blog\/?p=3870"},"modified":"2026-11-22T09:49:53","modified_gmt":"2026-11-22T01:49:53","slug":"do-other-check-valves-cause-pressure-drop-4ad3-107aee","status":"publish","type":"post","link":"http:\/\/www.weeklywineshow.com\/blog\/2026\/11\/22\/do-other-check-valves-cause-pressure-drop-4ad3-107aee\/","title":{"rendered":"Do other check valves cause pressure drop?"},"content":{"rendered":"<p>Hey everyone, let\u2019s cut to the chase. If you\u2019re a piping system pro, plant manager, or just someone who deals with fluid flow day-to-day, you\u2019ve probably wrestled with pressure drop. It\u2019s that annoying little loss of system pressure that throws off your designs, your efficiency, and even your bottom line. And if you\u2019ve ever shopped around for check valves, you\u2019ve likely wondered: Do <em>other<\/em> check valves cause pressure drop, too \u2014 or is that only a thing with certain types? <a href=\"https:\/\/www.zshvvalve.com\/gate-globe-and-check\/other-check-valve\/\">Other Check Valve<\/a><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.zshvvalve.com\/uploads\/47312\/small\/flange-bw-high-pressure-ball-valve64c35.jpg\"><\/p>\n<p>Full disclosure first: I\u2019m from a check valve supplier (I\u2019ll keep it casual here, no stuffy corporate jargon) and I work with all kinds of check valves, including the ones we call \u201cother types\u201d \u2014 you know, the ones that aren\u2019t the swing or ball check valves everyone\u2019s familiar with. Most people only hear about swing or ball valves when they talk about backflow prevention, but there\u2019s a whole world out there: lift check, dual plate, in-line, spring-loaded, even some specialty ones for harsh environments. And yeah, every single one of those \u201cother\u201d check valves will cause some pressure drop. But let\u2019s not jump to conclusions \u2014 it\u2019s not as simple as \u201call check valves suck pressure\u201d (pun intended, but keep it fair). The key is <em>how much<\/em>, and whether it\u2019s a problem for your specific system.<\/p>\n<p>First, let\u2019s get on the same page about what pressure drop even is. Pressure drop, for anyone new to the game, is the reduction in fluid pressure that happens when it flows through a component \u2014 in this case, a check valve. It\u2019s caused by two main things: friction between the fluid and the valve\u2019s internal parts, and the turbulence that happens when the fluid has to change direction or squeeze through gaps to get past the valve\u2019s closure mechanism. For a check valve, that closure mechanism is what makes it work: it opens when flow goes the right way, and slams (or closes gently) when flow tries to reverse. That mechanism is where most of the pressure loss comes from.<\/p>\n<p>Now, let\u2019s break down why \u201cother\u201d check valves are different from the swing or ball ones you might have worked with. Swing check valves are the OG, right? They have a hinged disc that swings out of the way when flow pushes it, so when it\u2019s fully open, the disc is almost parallel to the pipe wall. That means a lot of flow area is open, so pressure drop is pretty low \u2014 usually between 0.5 to 2 psi for most industrial fluids, depending on flow rate. Ball check valves use a metal or rubber ball that lifts off a seat when flow pushes it, but they often have smaller ports or the ball can rattle around, so their drop is a bit higher, like 1 to 3 psi. But what about those \u201cother\u201d check valves? Let\u2019s take spring-loaded lift check valves, for example. These have a disc that\u2019s pushed closed by a spring, and the spring has to compress to let flow through. Even when fully open, the spring and the disc take up space in the pipe, so flow has to squeeze through that gap. Turbulence gets worse here, so pressure drop can jump to 2 to 5 psi \u2014 sometimes even higher if the spring is too stiff, which makes it harder for low-flow systems to open the valve properly.<\/p>\n<p>Wait, dual plate check valves are another common \u201cother\u201d type, especially for large pipes in commercial HVAC or power plants. They have two hinged plates that fold back against the pipe wall when open, similar to a swing check but with a smaller footprint. But here\u2019s the catch: even when fully open, the plates create a slight obstruction, and the edge where the two plates meet can cause friction. Their pressure drop is usually around 1.5 to 3 psi \u2014 so a bit more than swing check, but less than spring-loaded lift. But I\u2019ve seen some cheap dual plate valves where the plates aren\u2019t aligned right, so the gap gets narrower, and pressure drop spikes to 6 psi just like that. That\u2019s why quality matters, even for \u201cother\u201d valves.<\/p>\n<p>Now, let\u2019s talk about specialty check valves \u2014 the ones that are often overlooked, hence the \u201cother\u201d label. For example, axial check valves, which are used in high-flow, low-pressure systems. These have a piston-like closure that moves along the axis of the pipe, so when open, it doesn\u2019t create much obstruction, right? Wrong \u2014 even axial valves have a seal around the piston that rubs against the pipe wall, causing small friction loss, and the piston\u2019s movement can create a tiny amount of turbulence. Their pressure drop is still lower than many other \u201cother\u201d valves, around 1 to 2 psi, but if you\u2019re running a system at ultra-low pressure (like less than 10 psi total), even 1 psi of drop is a big deal. That\u2019s the thing: pressure drop isn\u2019t just a number \u2014 it\u2019s relative to your system\u2019s operating pressure. If your system runs at 50 psi, a 3 psi drop is 6% loss, which is manageable. If it runs at 15 psi, that same 3 psi is 20% loss \u2014 that\u2019s a problem.<\/p>\n<p>Another \u201cother\u201d type: wafer check valves, which are super common in small piping jobs because they\u2019re thin and easy to install between flanges. Wait, no \u2014 wafer is a category, but some wafer check valves are the swing type, but many are the \u201cdual plate\u201d type, which we already talked about. But let\u2019s not confuse categories here. The point is, any check valve that\u2019s not a basic swing or ball falls into the \u201cother\u201d bucket for most people, and all of them have pressure drop because they have a closure mechanism that creates some flow restriction.<\/p>\n<p>Now, why do so many people ask if \u201cother\u201d check valves cause pressure drop? Because some manufacturers market certain valves as \u201clow-drop,\u201d and folks assume \u201cother\u201d ones don\u2019t. That\u2019s a myth. Every check valve, regardless of type, will cause at least a tiny bit of pressure drop \u2014 there\u2019s no such thing as a zero-drop check valve. The only question is how much, and whether you can mitigate it.<\/p>\n<p>Wait, let\u2019s get into the science a little more, because I don\u2019t want to be all vague. Pressure drop across a check valve is usually measured using a formula: \u0394P = (K * (v\u00b2 * \u03c1)) \/ (2g), where K is the resistance coefficient specific to the valve, v is flow velocity, \u03c1 is fluid density, and g is gravity. So K is the big one here \u2014 that\u2019s the number that tells you how much a valve resists flow. For swing check valves, K is around 0.5 to 1.5, while spring-loaded lift check valves have K values from 2 to 5. Axial check valves have K as low as 0.8, which is why their drop is lower. So if you know your valve\u2019s K factor, you can calculate the exact pressure drop for your system. That\u2019s a way better approach than guessing if \u201cother\u201d valves cause drop \u2014 you just look up their K rating (good suppliers will give this to you, no hiding it) and do the math.<\/p>\n<p>But here\u2019s the thing: pressure drop isn\u2019t always a bad thing. Wait, hear me out. Sometimes, a little extra pressure drop is intentional. For example, if you have a system where flow can reverse rapidly, a check valve with a bit more pressure drop might close faster, preventing water hammer. Water hammer is that loud, violent bang that can destroy pipes and equipment, so a slight pressure drop trade-off might be worth it. If you\u2019re dealing with water hammer, a spring-loaded check valve (which closes quicker than swing) might be better than a low-drop swing valve, even if it causes a bit more pressure loss.<\/p>\n<p>I\u2019ve seen this first-hand with a plant client a couple months back. They were using swing check valves in their cooling tower system, and they kept getting water hammer every time a pump shut off. They asked us about \u201cother\u201d check valves, and we recommended dual plate check valves. The initial worry was: \u201cWill the dual plate cause too much pressure drop?\u201d We calculated it would be 2 psi more than the swing valves, but their system operates at 80 psi, so that was a 2.5% loss \u2014 nothing. And the dual plate closed faster, eliminating the water hammer, which saved them $10k+ in pipe repairs every quarter. So it\u2019s a balance, not a one-size-fits-all.<\/p>\n<p>Another example: a small residential plumbing system. Wait, even residential has check valves \u2014 for sump pumps, water main backflow preventers. A lot of residential folks use wafer check valves (another \u201cother\u201d type) because they\u2019re easy to install in tight spaces. The pressure drop here is small, maybe 1 psi, but if your home has low water pressure (like from a well), that 1 psi can make your showers feel weak. In that case, you\u2019d want a lower K valve, like an axial check valve, even if it costs a bit more. The key is matching the valve\u2019s pressure drop to your system\u2019s needs.<\/p>\n<p>Now, let\u2019s address the elephant in the room: some \u201cother\u201d check valves do have way higher pressure drop than they should, because of cheap manufacturing. I\u2019ve seen no-name dual plate valves where the plates are made of thin, flimsy metal that warps, creating a narrow gap that restricts flow so much pressure drop jumps to 8 psi. That\u2019s not a property of \u201cother\u201d check valves \u2014 that\u2019s a property of bad valves. If you\u2019re sourcing from a reputable supplier (that\u2019s us, by the way), they\u2019ll test their valves to measure pressure drop, and provide clear K factors, so you know exactly what you\u2019re getting. No guesswork, no hidden fees for extra power to make up for pressure loss.<\/p>\n<p>Wait, let\u2019s clear up another confusion: check valves vs. backflow preventers. A lot of people group them together, but backflow preventers are a type of check valve, often with two check valves in series, which means <em>double<\/em> the pressure drop. But that\u2019s a separate conversation \u2014 the question here is about \u201cother check valves,\u201d so regular single check valves, not backflow assemblies.<\/p>\n<p>So to sum up the science: every check valve, including all the \u201cother\u201d types, causes pressure drop. The amount depends on the valve\u2019s design (closure mechanism, spring strength, port size), the fluid\u2019s flow rate and density, and the valve\u2019s quality. Swing check valves are among the lowest-drop \u201cstandard\u201d valves, while spring-loaded lift or poorly made dual plate check valves have higher drop. Specialty valves like axial are in between.<\/p>\n<p>Now, what does this mean for you? If you\u2019re designing a new system, or replacing check valves in an old one, don\u2019t just go with the familiar swing valve without checking your pressure requirements. If you have a high-flow, low-pressure system, go for a lower-drop \u201cother\u201d valve like axial. If you have a problem with water hammer, a slightly higher-drop dual plate or spring-loaded check valve might be the better pick. And always ask your supplier for the valve\u2019s K factor \u2014 that\u2019s the only way to accurately calculate pressure drop, no surprises.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.zshvvalve.com\/uploads\/47312\/small\/forged-steel-piston-check-valve8f1db.png\"><\/p>\n<p>I know a lot of folks stick to what they know, but \u201cother\u201d check valves aren\u2019t the boogeyman for pressure drop. They\u2019re just different designs for different jobs. The mistake is assuming that all \u201cother\u201d valves cause unnecessary loss \u2014 no, it\u2019s about matching the valve to your specific needs. If you\u2019re worried about pressure drop affecting your system\u2019s efficiency, or you\u2019re dealing with water hammer and standard swing valves aren\u2019t cutting it, don\u2019t guess. Hit us up to chat through your piping setup, what fluids you\u2019re moving, your flow rates, and what problems you\u2019re facing. We can walk you through which check valve (even the \u201cother\u201d ones) will give you the right balance of backflow prevention and minimal pressure loss, no jargon, no fluff.<\/p>\n<p><a href=\"https:\/\/www.zshvvalve.com\/gate-globe-and-check\/pipeline-valve\/\">Pipeline Valve<\/a> At the end of the day, pressure drop is just a part of working with fluid systems \u2014 the goal is to manage it, not eliminate it. \u201cOther\u201d check valves are a tool in that management, not a flaw. You just need to pick the right one for your job, and that\u2019s where we come in. If you\u2019re ready to stop guessing and start getting tailored advice on which check valve works best for your piping, reach out to connect and talk shop.<\/p>\n<hr>\n<p><a href=\"https:\/\/www.zshvvalve.com\/\">Wenzhou Zhenshun Valve Co., Ltd.<\/a><br \/>As one of the most professional other check valve manufacturers and suppliers in China, we&#8217;re featured by quality products and low price. Please rest assured to buy cheap other check valve made in China here from our factory. Also, quotation is available.<br \/>Address: Heyi Industrial Zone, Oubei Street, Yongjia County Wenzhou, Zhejiang China<br \/>E-mail: info@zshvvalve.com<br \/>WebSite: <a href=\"https:\/\/www.zshvvalve.com\/\">https:\/\/www.zshvvalve.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"<p>Hey everyone, let\u2019s cut to the chase. If you\u2019re a piping system pro, plant manager, or &hellip; <a title=\"Do other check valves cause pressure drop?\" class=\"hm-read-more\" href=\"http:\/\/www.weeklywineshow.com\/blog\/2026\/11\/22\/do-other-check-valves-cause-pressure-drop-4ad3-107aee\/\"><span class=\"screen-reader-text\">Do other check valves cause pressure drop?<\/span>Read more<\/a><\/p>\n","protected":false},"author":136,"featured_media":3870,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3833],"class_list":["post-3870","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-other-check-valve-4a43-10b372"],"_links":{"self":[{"href":"http:\/\/www.weeklywineshow.com\/blog\/wp-json\/wp\/v2\/posts\/3870","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.weeklywineshow.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.weeklywineshow.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.weeklywineshow.com\/blog\/wp-json\/wp\/v2\/users\/136"}],"replies":[{"embeddable":true,"href":"http:\/\/www.weeklywineshow.com\/blog\/wp-json\/wp\/v2\/comments?post=3870"}],"version-history":[{"count":0,"href":"http:\/\/www.weeklywineshow.com\/blog\/wp-json\/wp\/v2\/posts\/3870\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.weeklywineshow.com\/blog\/wp-json\/wp\/v2\/posts\/3870"}],"wp:attachment":[{"href":"http:\/\/www.weeklywineshow.com\/blog\/wp-json\/wp\/v2\/media?parent=3870"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.weeklywineshow.com\/blog\/wp-json\/wp\/v2\/categories?post=3870"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.weeklywineshow.com\/blog\/wp-json\/wp\/v2\/tags?post=3870"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}